You are looking at historical revision 28324 of this page. It may differ significantly from its current revision.
Since CHICKEN generates C code, it is relatively easy to create programs and libraries for a different architecture than the one the compiler is executing on, a process commonly called cross compiling. Basically you can simply compile Scheme code to C and then invoke your target-specific cross compiler. To automate the process of invoking the correct C compiler with the correct settings and to simplify the use of extensions, CHICKEN can be built in a special "cross-compilation" mode.
Note: in the following text we refer to the "target" as being the platform on which the software is intended to run in the end. We use the term "host" as the system that builds this software. Others use a different nomenclature or switch the meaning of the words.
Make sure you have a cross-toolchain in your PATH. In this example, a Linux system is used to generate binaries for an ARM based embedded system.
Building the target libraries
First you need a version of the runtime system (libchicken), compiled for the target system. Obtain and unpack a tarball of the CHICKEN sources, or check out the code from the official code repository, then build the libraries and necessary development files:
make ARCH= \ PREFIX=/usr \ PLATFORM=linux \ HOSTSYSTEM=arm-none-linux-gnueabi \ DESTDIR=$HOME/target \ TARGET_FEATURES="-no-feature x86 -feature arm" \ install
This will build CHICKEN and install it in ~/target, which we use as a temporary place to store the target files. A few things to note:
- ARCH is empty, since we don't want the build process to detect the architecture (since the target-architecture is likely to be different).
- PREFIX gives the prefix on the target system, under which the libraries will finally be installed. In this case it will be /usr/lib.
- PLATFORM determines the target platform. It must be one of the officially supported platforms CHICKEN runs on.
- HOSTSYSTEM is an identifier for the target system and will be used as the name prefix of the cross C compiler (in this case arm-none-linux-gnueabi-gcc). If your cross compiler does not follow this convention, pass C_COMPILER and LIBRARIAN to the make(1) invocation, with the names of the C compiler and ar(1) tool, respectively.
- DESTDIR holds the directory where the compiled library files will temporarily installeds into.
- TARGET_FEATURES contains extra options to be passed to the target-specific Scheme translator; in this case we disable and enable features so that code like the following will do the right thing when cross-compiled:
(cond-expand (x86 <do this ...>) ...)
- If you obtained the sources from a source-code repository and not from an official release tarball, you will need a chicken executable to compile the Scheme sources of the runtime system. In this case pass yet another variable to the make(1) invocation: CHICKEN=<where the "chicken" executable is.
- You can also put all those variables into a file, say config.mk and run make CONFIG=config.mk.
You should now have these files on ~/target:
|-- bin | |-- chicken | |-- chicken-bug | |-- chicken-install | |-- chicken-profile | |-- chicken-status | |-- chicken-uninstall | |-- csc | `-- csi |-- include | |-- chicken-config.h | `-- chicken.h |-- lib | |-- chicken | | `-- 6 | | : | | | |-- libchicken.a | |-- libchicken.so -> libchicken.so.6 | `-- libchicken.so.6 `-- share |-- chicken | |-- doc : ; : | | | `-- setup.defaults `-- man `-- man1 :
You should now transfer libchicken.so to the target system, and place it in /usr.
Building the "cross chicken"
Next, we will build another chicken, one that uses the cross C compiler to generate target-specific code that uses the target-specific runtime library we have just built.
Again, unpack a CHICKEN release tarball or a source tree and run make(1) once again:
make PLATFORM=linux \ PREFIX=$HOME/cross-chicken \ TARGETSYSTEM=arm-none-linux-gnueabi \ PROGRAM_PREFIX=arm- \ TARGET_PREFIX=$HOME/target/usr \ TARGET_RUN_PREFIX=/usr \ install
- PREFIX gives the place where the "cross chicken" should be installed into. It is recommended not to install into a standard location (like /usr/local or $HOME) - some files will conflict with a normal CHICKEN installation.
- TARGETSYSTEM gives the name-prefix of the cross C compiler.
- PROGRAM_PREFIX determines the name-prefix of the CHICKEN tools to be created.
- TARGET_PREFIX specifies where the target-specific files (libraries and headers) are located. This is the location where we installed the runtime system into.
- TARGET_RUN_PREFIX holds the PREFIX that will be effective at runtime (so libchicken.so will be found in $TARGET_RUN_PREFIX/lib).
- Make sure to use the same version of the CHICKEN sources for the target and the cross build.
- If you build the cross chicken from repository sources, the same note about the CHICKEN variable applies as given above.
In ~/cross-chicken, you should find the following:
|-- bin | |-- arm-chicken | |-- arm-chicken-bug | |-- arm-chicken-install | |-- arm-chicken-profile | |-- arm-chicken-status | |-- arm-chicken-uninstall | |-- arm-csc | `-- arm-csi |-- include | |-- chicken-config.h | `-- chicken.h |-- lib | |-- chicken | | `-- 6 | | : | | | |-- libchicken.a | |-- libchicken.so -> libchicken.so.6 | `-- libchicken.so.6 `-- share |-- chicken | |-- doc : ; : | | | `-- setup.defaults `-- man `-- man1 :
To make sure that the right C compiler is used, we ask arm-csc to show the name of the cross C compiler:
% ~/cross-chicken/arm-csc -cc-name arm-none-linux-gnueabi-gcc
Compiling simple programs
% ~/cross-chicken/arm-csc -v hello.scm /home/felix/cross-chicken/arm-cross-chicken/bin/arm-chicken hello.scm -output-file hello.c -quiet arm-none-linux-gnueabi-gcc hello.c -o hello.o -c -fno-strict-aliasing -DHAVE_CHICKEN_CONFIG_H -g -Wall \ -Wno-unused -I /home/felix/cross-chicken/arm-chicken/include rm hello.c arm-none-linux-gnueabi-gcc hello.o -o hello -L/home/felix/cross-chicken/arm-chicken/lib -Wl,-R/usr/lib -lm \ -ldl -lchicken rm hello.o
Is it an ARM binary?
% file hello hello: ELF 32-bit LSB executable, ARM, version 1 (SYSV), for GNU/Linux 2.6.16, dynamically linked (uses shared libs), not stripped
Yes, looks good.
By default, the tools that CHICKEN provides to install, list and uninstall extensions will operate on both the host and the target repository. So running arm-chicken-install will compile and install the extension for the host system and for the cross-target. To selectively install, uninstall or list extensions for either the host or the target system use the -host and -target options for the tools.
Sometimes an extension will only be compilable for the target platform (for example libraries that use system-dependent features). In this case you will have to work around the problem that the host-compiler still may need compile-time information from the target-only extension, like the import library of modules. One option is to copy the import-library into the repository of the host compiler:
# optionally, you can compile the import library: # ~/cross-chicken/arm-csc -O3 -d0 -s target-only-extension.import.scm cp target-only-extension.import.scm ~/cross-chicken/lib/chicken/6
Cross-development is a very tricky process - it often involves countless manual steps and it is very easy to forget an important detail or mix up target and host systems. Also, full 100% platform neutrality is hard to achieve. CHICKEN tries very hard to make this transparent, but at the price of considerable complexity in the code that manages extensions.